RICK REA: Helping You Grow Through Online Marketing
  • Home
  • Blog
    • Social Media News
    • SEO Marketing News
    • Digital Trends News
    • Photography News
    • Mobile Marketing
    • Business News
    • Gadget News
    • Printing News
  • Contact
  • About
  • Subscribe

Printing News



University of Twente Researchers 3D Print Gold Microstructures Using LIFT Technique

10/31/2018

0 Comments

 
https://ift.tt/2AD2VbB

University of Twente Researchers 3D Print Gold Microstructures Using LIFT Technique

https://ift.tt/2PsKqPp

Researchers at the University of Twente have developed a new laser printing technique that allows for the 3D printing of gold nanostructures, including complex overhanging structures. By pointing a very short laser pulse onto a nanometer-thin metal film, a tiny droplet of liquid metal is ejected onto the substrate, where it solidifies. The technique is called laser-induced forward transfer, or LIFT. The researchers have been using it to build tiny, complex structures out of copper and gold; the copper acts as a mechanical support for the gold.

LIFT will enable the 3D printing of micro components for electronics or photonics. The example that the researchers use is a tiny helix, which could act as a mechanical spring or an electrical conductor at the same time. The helix is printed with copper around it, forming a copper box, which prevents a drop meant for a new winding from landing on the previous winding. After the helix is completed, the copper is etched away chemically, leaving a helix of pure gold, just a few tens of microns in size.

The volume of the droplets is a few femtoliters, and have the diameter of a little more than one nanometer. A short pulse of green laser light is used to melt the gold and copper. The researchers were concerned that the two metals would mix, but that wasn’t the case. The drop by drop method used to build the microscopic structures results in high resolution, with a surface roughness of only 0.3 to 0.7 microns.

The research is documented in a paper entitled “Printing of complex free-standing microstructures via laser-induced forward transfer (LIFT) of pure metal thin films.“

“The further reduction of Au porosity will be the topic of future work, for instance through laser re-melting, conventional sintering or better understanding of the droplet impact behavior,” the researchers state. “Also, heating of the receiver could reduce thermal stresses and possibly splashing of droplets. Smaller structures could be achieved through minimizing stress on small features, e.g. through critical point drying, more precise sample manipulation and smaller droplet sizes. This study demonstrates that LIFT can be used for functional 3D printing with very small features and using pure materials which is important for use in electronics or micromechanics.”

The LIFT technique can also be used for other metals or combinations of metals. It has a lot of potential for use in applications such as electronic circuits, micromechanical devices and sensing for biomedical applications. Using copper as a “sacrificial” material allows for more complex structures to be 3D printed, such as those with overhangs, like the helix. This technique, like other additive manufacturing techniques, has the potential to save time and money while allowing for the production of intricate components.

The research was carried out by the departments of Mechanics of Solids, Surfaces and Systems (MS3) and Design, Production and Management (DPM), both part of the Engineering Technology faculty of the University of Twente. The researchers also collaborated with DEMCON Corporation, a spinoff company of the University of Twente.

Authors of the paper include Matthias Feinaeugle, Ralph Pohl, Ton Bor, Tom Vaneker and Gert-willem Römer.

Discuss this and other 3D printing topics at 3DPrintBoard.com or share your thoughts below.

 





Printing

via 3DPrint.com | The Voice of 3D Printing / Additive Manufacturing https://3dprint.com

October 31, 2018 at 02:39PM


0 Comments



Leave a Reply.

    Categories

    All
    3-D Printed Ultrasound Models
    3-D Printing
    3D Printing
    Tools For The Visually Impared
    Visually Impared

    Archives

    May 2023
    April 2023
    March 2023
    February 2023
    January 2023
    December 2022
    November 2022
    October 2022
    September 2022
    August 2022
    July 2022
    June 2022
    May 2022
    April 2022
    March 2022
    February 2022
    January 2022
    December 2021
    November 2021
    October 2021
    September 2021
    August 2021
    July 2021
    June 2021
    May 2021
    April 2021
    March 2021
    February 2021
    January 2021
    December 2020
    November 2020
    October 2020
    September 2020
    September 2019
    August 2019
    July 2019
    June 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    November 2018
    October 2018
    September 2018
    August 2018
    July 2018
    June 2018
    May 2018
    April 2018
    March 2018
    February 2018
    January 2018
    December 2017
    November 2017
    October 2017
    September 2017
    August 2017
    July 2017
    June 2017
    May 2017
    April 2017
    March 2017
    February 2017

    RSS Feed

Powered by Create your own unique website with customizable templates.
  • Home
  • Blog
    • Social Media News
    • SEO Marketing News
    • Digital Trends News
    • Photography News
    • Mobile Marketing
    • Business News
    • Gadget News
    • Printing News
  • Contact
  • About
  • Subscribe