https://ift.tt/2QCZs79
3D Printing Bikes: A Pedalution, Part 3 Value Chain Disruptions with 3D Printing https://ift.tt/34YFEPF In the first installment of this series, we looked at how 3D printing is being used in bicycles. In the second article, we went deeper and also examined 3D printing for e-bikes. On the whole, we concluded that many small players are using 3D printing to make polymer and metal bicycle components. Some of these are commercially viable and even successful. One of the most fruitful could be the 3D printing of lugs. These unique lugs can be used in combination with regular tubing to make custom frame geometries. If we look into the near-future, custom, 3D printed carbon and 3D printed metal frames could become a reality. Given the fact that weight saving is so crucial in bikes, we can also expect a lot of weight-saving lightweight components. Usually a reduction in part count is also a good reason to use 3D printing, but this is more difficult to achieve in the case of bicycles. Different families of components are made with different suppliers, e.g., Selle Italia for seats, Reynolds for tubing, and Campagnolo for groupsets. At the same time, groupsets would need very high-quality 3D prints and finishing, leaving only powder bed fusion as a possibility, while other components such as seat stays could use less critical post-processing. Other components would be polymer or made to entirely different quality standards. Broadly speaking, the above are listed as to how likely they are to happen, given how easy it would be for that instance to occur given the investment, place in the value chain, and dynamism of that player.
The aforementioned is meant to be a general helicopter view of the market entry opportunities and opportunities for players in the bicycle market using 3D printing. As we have seen in orthopedics, hearing aids, and other markets that have fundamentally been disrupted by 3D printing, there are wholesale disruptions in the value chain. Aggressive, opportunistic, strategically acute, or cash-rich players have all leapfrogged their positions in the value chain via 3D printing. Generally what we’ve seen is that some companies realize the importance of 3D printing in creating components that are low-volume, high-performance, unique, weight-saving or quicker-to-market. In orthopedics, for example, Stryker has capitalized on the capabilities of 3D printing to make parts that have better bone adhesion because we can create the right surface texture to promote osseointegration. At the same time, through lattice structures and the like, we can more closely approximate the modulus of bone, which makes the implant less likely to cause issues, such as stress shearing. We can also make a relatively low-volume production runs, allowing us to manufacture many different sizes and different implants in the same builds, with the same materials and the same processes. In the future, we could in the future also have individualized orthopedic implants that may make the fit better and lead to less blood loss and faster recovery. At the same time we can produce implants that are tough and wear-resistant enough to work as “structural” orthopedic implants. And the cherry on top in orthopedics is that we are significantly cheaper than conventionally manufactured implants by a factor of ten. We can meet the required surface roughness, tolerances and production speeds, and prices as well. And perfection is important since faults in devices or in operations can cost thousands or millions. In this case 3D printing orthopedics is the best business case out there. Another business case that is very good, but in a different way, is the 3D printing of rocket engines. For many of these parts, we can match the performance of cast and forged parts, while producing components within the tolerances and costs required. What’s more we can make more lightweight structures, optimize surface textures for ignition and flow, and reduce part count. Reducing part count means less money tied up in tooling and upfront cost, while we have significantly fewer production steps, which means that six sigma excellence is easier. Moreover, we can produce components, iterate, and go from drawing-to-part faster, as well. Typically, here we’re looking at the potential of what I call 40/40/40/40/40. The five forties are:
The five forties have been achieved in a number of industries, but will not be achievable in all industries. Commoditization, size, and specific characteristics that are hard for us to achieve (smoothness, color) could make it impossible in some other fields. But, if we look at the relative importance of the five forties and the 11 scenarios for bikes, what do we expect to happen? Printing via 3DPrint.com | The Voice of 3D Printing / Additive Manufacturing https://3dprint.com June 8, 2021 at 08:03AM
0 Comments
Leave a Reply. |
Categories
All
Archives
April 2023
|